Friday, April 17, 2009

Parts Prep - day 3

The last of the metal parts are now dusty-gray as I completed the bead-blasting efforts. This Mid has a motor plate heatsink salvaged from an old circuit board. It doubles as a body mount with one of the standard Mid plastic parts. I blasted the gold anodize off and reground the interface to the motor plate for good heat transfer. Pretty classy and indeed a functional piece of bling, if I do say so myself:



The front and rear a-arm plates were also blasted to complete the set. ...And you're saying "...what about the motor plate?". I think that the motor plate is best left as-is since the motor and mounting screws need to slide back and forth, which requires a smooth surface. The heatsink interface too needs to be smooth. Therefore, these last few parts should complete the sparkly icy gray aesthetics of this buggy:



And I've decided on the front diff gears; I'm using the 18T/Nil combo when I rebuild it. Reason being, you really don't want to underdrive the front end of a 4WD buggy. This would be worse than trying to drive a 2WD car, which, I for one, can't drive worth beans. Perhaps someone will correct me on this, in which case I have plenty of new spare 19T gears that I will include in the kit. Either way, you have to disassemble the front end to make the swap. One of the reasons for this decision is the rear Diff. Take a close look and wonder at its uniqueness:



Indeed, that is a dual chaindrive rear ball differential... quite custom. The teeth and belt gears were machined off of the Optionhouse ball diff and stock chain gears were machined to slip right onto the housing. A little superglue and wallah, dual chaindrive ball diff! Yes, I like having a ball diff on the rear of a high speed road buggy. It guarantees having drive on the outside wheel in case the inside wheel gets a little light. Not so for the front end. I like to leave the front wheels very independent with a smooth free running set of bevel gears. Just to be clear, I've decided to bring this car back to its glory as a dual chaindrive Optima Mid Hybrid. This will keep this car absolutely unique to every degree in the Kyosho line.

I have also been a bit worried about what to do about a ESC. At one time, I loaned the ESC, a Novak all custom wired for this buggy, to an old race partner. Somehow I ended up with 3 other speed controllers in my box... an old Futaba with reverse, no stickers; a Tekin that looked pretty much toasted with wires missing and such; and a Tekin TSC 411P with Torque Control. It must be an early model as it didn't have the fuse built in. It is wired with compatible connectors and the control wires can easily be modified. Luckily I could easily discern the Novak receiver's pinout... as this is hardwired with a flying lead. This is the unit that I will use:



I charged a 7-cell battery pack and loaded a set of AA's into the old, beat up Magnum Senior radio. It took a little convincing, but the radio finally decided to behave. I think I need to make a remote battery cable for it if I don't want it glitching out on me. The radio has more buttons and knobs then I ever wanted. I adapted the ESC control cable to the receiver with a set of pins; plugged in the battery; and turned on the radio and the ESC switch... and crossed my fingers no smoke escaped from the electronics. I waited to plug in a motor so I commenced with dialing in the steering. I was anxious to see how well the new linkage would work. With much fiddling and fondling the radio knobs, I finally figured out what did what. Here is a shot of the setup:



I was really happy that the ESC powered the receiver properly and supplied power to the servo. Here is the steering linkage in action:



Next, the motor test. I wasn't sure what the blinking radio power indicator meant... this radio is a 3-channel radio for gas systems which has a warmup switch. The motor was acting a little weird when I first plugged it in. Then I figured out what the proper setting should be... the light should be on solid by turning warmup off... DUH!

It didn't take much to dial in the ESC and the radio for the motor. The brake trim is a bit touchy but all that will be dialed in on the road. I ran it on a modified "green" motor; an old Rev Tech maybe. Not wanting to throw a winding or stress the brake FET, I decided to just chill it and be satisfied with the fact that I have a functional setup for when the car is complete. I'll post the radio here just to archive the knob's positions for later:



One of the things I haven't been able to show you is the battery position. I learned a long time ago on another Optima that a lengthwise battery makes the car very stable in corners... stick to the ground, so to speak. This car can hold a 6-cell or 7-cell pack. The 6-cell is a normal stick, while a 7-cell has 3 cells side by side in the middle. I haven't seen this configuration in a commercial pack, but it is quite easy to make. Once I get around to running the car you will see what I mean, but for the meantime, this is the motor end of the battery holder. That's right, the battery lays right on top of the chain groove in the chassis:



Thursday, April 16, 2009

Parts Prep - day 2

To follow up on yesterday, the front side-plates were bead-blasted to match the base. A little grinding smoothed out some of the unused features. Gotta love the way a bit of blasting erases so many years of abuse:



The real task for today was refurbishing the chassis. A chunk of fiberglass that started life as a peg-board circuit test fixture salvaged in a warehouse clearance give-away. A small router table, a Dremel tool, and some careful planning and fixturing brought this chassis into shape. Holes are tapped directly in the fiberglass. Some of the holes were not perfectly made, and some trackside chain repairs have allowed some desperate alterations to compromise the holes. Today, all the M2,5 holes were deepened and retapped. All were salvaged and the new screw of choice is a Schroff offering for their electronics racks. Their length and large head diameter is uniquely appropriate for this application. Here is a closeup of the screw:



Having limited access to real shop tools does have its advantages. The pilot holes and the tapping were done with much greater precision that the 1st time around. The other mod required, as eluded to yesterday, was to counterbore the holes for the steering linkage - pivots. This was done with a drill press and a 7,5mm mill bit. It was a bit touchy trying to keep the bit centered over the hole. But if you recall, the 1/4" hex shaft required a 3mm deep counterbore. As you can see, this was accomplished beautifully:



And a 2nd plus about this revised features; all the screws are the same:



...except these, which I had to nip the tops off of:



When I assembled the plastics, the tips of the front sideplate screws now protrude past the plastic. A quick nip of the front gearcase took care of that:



Here is a shot of the steering linkage installed:



...and the sideplates:



...and with the diff case:



...and this is a 1,000 words all put into technicolor!



A final word about this chassis: all these tapped holes are M2,5 with plenty of material for M3 tapping. Some custom undercut M3 screws [captured hardware] could be used. That simply means that there is an M3 hole tapped in the metal plate slots and drive the screws in [captured]. Once loosely fastened to the chassis, the slots would work as before to adjust the chain.

Of course, this level of progress only begs the other questions that must be answered... Which drivetrain?

I've wondered if I can belt-drive this setup. I have all fresh [new] parts to make this a sweet belt drive buggy: new ball diffs; hardened pinion; new cases; new spur gears and full bearing set... but alas, this chassis is a long chassis that requires a different belt length. And I don't know what that length would be. It also turns out that Kyosho took a standard belt type... the XL series, and ordered a special narrow version of it. So this makes industrial suppliers less likely to want to talk to us hobbyists. So, since this buggy has always been a chaindrive buggy... and chaindrives are ~very~ efficient [and rebuildable!], we will stick with chaindrive.

The front differential is in perfect shape. The bearing spin freely, dirt and dust is absolutely minimal and the bevel gears spin quite freely and smoothly. The washers at the bearings are a great way to avoid dirt in the bearings. It could go back in as is and it would be perfect... but then again, a rebuild demands inspection, and since I have dozens of unused chain gears, I could dedicate a new set of plastics to the rebuild. Even the dogbone drivers are in really good shape signifying the low hours on this car. This car has been run using stock class motors for the most part. Now my dilemma... 18T/19T or 18T/Blank?



This is only the beginning of difficult choices. I have every intention to make the rebuild on-road compatible. This means that I don't want the front wheels over/underdriven. This is a good reminder of this unique option provided on the original Optima. At one point, I obtained a belt drive gear with this function but it never went anywhere. The real difficult choice is still looming in the back of my mind... dual chain drive ball diff or conventional diff and conventional gearing for the gearbox. Stay tuned!

Wednesday, April 15, 2009

Parts Prep - day 1

Now that the car is a basket case, it is a good time to start working on the individual parts and functions. Last night was the recovery of the front bottom plate. Yep, that is the original Optima plate, this one from the parts bins. I prefer this part because the slotted holes were not countersunk. This will making chain tension adjustments much easier. Here is the "before" shot of the front end:



Notice the steering linkage resembles that of the Ultima with the floating beam connected to the tie rods. The beam is carbon fiber shimmed with washers and attached with kingpin bolt. The rest of the linkage is stock original Optima complete with the posts that are attached with the M2,5 screws. When I disassembled the car, the bolt on the saver side [left] broke and was stuck in the aluminum tube. Sorry to say I didn't have any spares so a little fabrication was necessary. I decided that I could change the design a bit as this car has a solid chassis rather than the rails. I will be counterboring the fixed steering pins into the chassis. The aluminum strap normally on the Optima is not needed. Here is a shot of the steering linkage with the new pins and special washer:




The new pivots are made of brass and the small brass hex pieces are washers for the flathead screws. Nice thing is, the hex is 1/4"; the clearance is appropriate between the two parts; and the fit is just about perfect. A dab of bicycle bearing grease and all is good. Notice the large washers... these are used to preload the servo-saver spring. There is a servo-saver on the servo itself so this is just gravy. Here is a closeup of the pivots assembled:



Now to add the tie rod assembly:



And finally a shot of the assembled linkage: [tie-plate present only for stabilizing the assembly]



That pretty much does it for the steering linkage. Nice smooth action, solid and extreme range. So far so good.

The tape that was used to seal the front case was quite stubborn. It took some serious convincing to remove, but the effort was well worth it. You will notice that the cases were modified to account for the mono-shock. This leaves a hole that needs covering. As this build progresses, i will see if there is a better way to deal with this unwanted feature. Here are a few shots of the cases and the salvaged bottom plate:




Notice the difference in the setscrew sizes for the a-arm shafts. It is good to know that a case can be salvaged buy tapping out the hole for the next size setscrew. I may go back and make them match.

The bottom plate was pretty rough. It has seen quite a few high flying jumps but overall, it was in pretty good shape. Kyosho had put forth several thicknesses of this part. This one is 1,5mm thick. The previous one was 2,0mm thick. I also took the hammer to lowered portion of the plate where the chain-guide use to be. This can be flat in this application. This also makes the underside flat. If you look carefully at the image, you will also see where I files the transition of the chain from the differential stamping to the flat part. That should help save a chain or two. Here are some pics of the bottom plate after bead-blasting. Cleaned up pretty nicely, don't you think?




Looks like I will be following up on the rest of the front assembly in the next few day. This means that chassis mods are coming soon. Stay tuned.

Tuesday, April 14, 2009

Awakening!

Many moons have drifted across the horizon since the day this subject has seen the light of day. Had it not been for the ever increasing need for horizontal space, many more moons may have simply drifted by until one day this blast from the past would simply have found its way onto a table at the local flea market or neighborhood garage sale.

"What the heck are you talking about!" I hear crowing in the distance...

In a past life, many days were spent with a hobby so gripping that hardly anything else was important. It started out innocently enough... a small investment in a toy remote controlled car simply to pass the time. A pretty natural hobby choice for a technical tinkerer. Well, if I had only known all that followed for nearly a decade.

The RC car I choose was a KYOSHO JAVELIN. A 4WD 1/10th scale off-road racer. Little did I know that this model would one day become a very competitive race car.

Of course, the first thing one finds out about RC cars is that "upgrades" are available... which brings you into the hobby store... where you find out the "hobby" is also a competitive sport! Sport! ...you say? "Ha... another hooked" is what was going through the mind of the owner of RC Modeler NW, one of the ma and pop shops in Beaverton Oregon. Yep... that's how it started.

The purpose of this blog is not to reminisce about the good 'ol days. No, the purpose of this blog is to chronicle the rebuilding of one of the offspring spawned from the bags and boxes of parts that originated from what I affectionately refer to as "the pegboard catalog"... meaning the wall of replacement and upgrade parts at the hobby stores.

3rd party parts suppliers were not going to be outdone either. For every good race car, there are others that feel they can do better. Companies like Thorp, MRC, A&L Manufacturing, and many others help contribute to the fever of faster, further, and higher. Some great advancements made the sport more competitive and ever more addictive.

We fast forward several years to when Kyosho pretty much ended their rear engine Optima series. Kyosho's next offering was a mid-ship motor model named aptly, the Optima Mid. Some vast improvements were made in the gear-train as well as standardizing many of the upgrade parts that Kyosho offered under their OptionHouse brand. The real wisdom in Kyosho's line is the backwards compatibility of so many parts and options.

Having invested heavily in the 1st generation Optima, and being intrigued with the new generation, I began a project joining the best of both models. The new mid-engine design was pretty much a no-brainer. Longer wheelbase models were pretty much the rage as well... and on the track, one model was just a smoking machine that glued itself to the track and flew! I'm referring to the Yokomo 4wd. The unique feature of this car was an independent mono-shock front end.

Another influence in the new build was a little known, short lived 1/10th scale model that I cannot even recall the name of. The chassis was made form 2 carbon fiber side plates, orange a-arms, and the very same chain-drive as in the original Optima. What was unique about this car is the fact that not only the fwd was chain-drive, but the final pinion was also a chain-drive, eliminating a counter gear in the setup. Another unique feature of this drive train was the simple spur gear adapter plate. This made it simple to bolt on just about any spur gear.

Okay, I am armed with all I want in a 1/10th scale 4WD off-road racer. My skills were honed to be dangerous with a Dremel tool... specifically the cutoff wheels. I learned to fabricate plates from a single carbon fiber sheet I purchased off the pegboard catalog. That sheet was used for years of fabrication. The bigger challenge was the chassis. Having learned let level of punishment these cars have to endure, this was not an easy choice. Cars have been known to fly 6-7ft in the air and land 20 feet later. These machines are not always to graceful about landing, either. That is why most come with bumpers [like that does any good!].

Oh yea... the purpose of this blog is to recap the building of this unique Optima Hybrid Mid RC car. I will chronicle the rebuilding of this car in order to capture the nuances of its design. I will likely rebuild it differently that the original intent simply because today's motors are much more powerful and run-times are 3x what they use to be. I do not envision this creation finding itself back on the racetrack. Not that it cannot do this, but more that there is no reason to. This will be up to the new owner. Yes, the new owner! I am rebuilding this car with the intent to sell it. This blog will capture the subtleties in care and maintenance of this car.

Please follow along as this journey commences. This is the status today: